PTFE ƒe dzoxɔxɔ gã ƒe tepe ƒe nuwuwu mo ƒe wɔwɔme si wotso la kpɔa ŋusẽ ɖe adhesive oozing kple nugbɔ kɔkɔ dzi tẽ le etsɔtsɔ wɔe me. Gbegblẽ nyuie o (aŋutsrɔe siwo me mekɔ o, dzogoe si mesɔ o) wɔa aŋe ƒe ka, enaa nugbɔ ƒe nulénu ƒe ƒuƒoƒoa nɔa sue, eye wòɖea fiberglass burrs ɖe go – si wɔnɛ be tsi dona, kadodo si gbɔdzɔ, eye wòkɔna le dzoxɔxɔ alo teteɖeanyi te. Nuwuƒe mo siwo mesɔ o (siwo le ƒutsotsoewo me, siwo dona ɖe gota) hea nyaƒoɖeamenu ƒe mama si mesɔ o vɛ, si wɔnɛ be adhesive creep le edzraɖoɣi. Nuwuƒe mo nyuitɔ la le gbadzaa, le tsia dzi, eye megblẽa nu le eŋu o – ewɔa dɔ abe nutrenu si xea nulénu la eye wòkpɔa egbɔ be nugbɔ ƒe kadodo bliboe.

Le PTFE tape coating me la, solvent volatilization rate of silicone pressure-sensitive adhesive nye dɔwɔwɔ ƒe nɔnɔme vevi aɖe. Kabakaba akpa → ŋutigbalẽ ƒe ʋuʋu le anyigba dzi, eƒe anyigba ƒe ƒuƒuiƒe nyuie o, pinholes (trepped solvent), kple craters (condensation alo contaminant-induced). Blewu akpa → sagging, eƒe gowo le ɣie, kple dewetting le low-surface-energy PTFE dzi. Mɔnu nyuitɔ: blewu gbãtɔ volatilization na leveling kple bubble sisi, emegbe kabakaba ƒuƒu hena nɔnɔmewɔwɔ. Zã atike siwo wotsaka (toluene/xylene + esi ƒuna kabakaba) kple dzodoƒe ƒe dzoxɔxɔ si le tɔtrɔm (si le bɔbɔe→ti titina→kɔkɔ).

PTFE ƒe dzoxɔxɔ gã ƒe tape la te ŋu nɔa te ɖe dze sisi nu nyuie ŋutɔ, gake nusiwo gbɔdzɔe nye nusi léna ɖe nu ŋu kple fiberglass substrate ƒe goawo. Dodokpɔmɔnu: 1000h neutral salt spray (NSS) dodokpɔ, dzidzedze le peel ƒe ŋusẽ léle ɖe te (≥80% hiã), ŋku ƒe gbɔdzɔgbɔdzɔ (kɔkɔ, blistering), kple ga substrate ƒe xɔxlɔ̃. Le ƒumelãwo kple nuto siwo me dze sɔ gbɔ ɖo gome la: zã silicone PSA (menye acrylic o), PTFE substrate si me wode tsii bliboe, tsɔ nutrenu si te ŋu nɔa te ɖe yame ƒe nɔnɔme nu xea goawo nu, eye nàtsɔ primer asisi ɖe ga ŋu.

PTFE ƒe dzoxɔxɔ gã ƒe tape megaléna ɖe eŋu o le eŋudɔwɔwɔ enuenu megbe le ɖiƒoƒo si le eƒe go dzi (ke, silicone ami), adhesive cohesive failure (nu susɔe), alo substrate ƒe kadodo si gbɔdzɔ ta. Egbɔkpɔnuwo: silicone PSA si ƒe crosslink lolo (ʋuʋudedi sue, tack/holding power si da sɔ), primer ƒe atikewɔwɔ ɖe PTFE substrate dzi, dense fiberglass backing, kple eŋudɔwɔwɔ nyuie (anyigba siwo le dzadzɛ, peel fafɛ, 180° angle). Agbɔsɔsɔme dodokpɔ ɖoa ​​kpe ŋgɔyiyi dzi.

PTFE ƒe dzoxɔxɔ gã ƒe tape si wodzra ɖo le nɔnɔme aɖewo koŋ me (10-25°C, 40-70% RH, adzɔge tso UV/nyaƒoɖeamenu sesẽ gbɔ) ƒe agbenɔƒe si woɖo ɖi la nye ɣleti 3-6 (dzidzenu nyuitɔ vaseɖe ɣleti 12). Nu vevi siwo gblẽa nu le eŋu: mele be lãgbalẽ ƒe ŋusẽ naɖiɖi wu 70% le asixɔxɔ gbãtɔ me o; nusi léna ɖe nu ŋu ƒe akpa aɖeke meli le dzoxɔxɔ gã aɖe ɖeɖeɖa megbe o; carbonization alo cracking aɖeke mele dzoxɔxɔ si woɖo ɖi me o. Dodokpɔ kabakaba: asi ʋuʋu ƒe seselelãme, 260°C ƒe nugbagbevi susɔe dodokpɔ, kple lamination shrinkage dodokpɔ.

PTFE tape si woxatsa ate ŋu atu interlayer adhesion (blocking) kple adhesive transfer le ɣeyiɣi didi ƒe nudzraɖoƒe. Nusiwo gbɔ wòtso: PTFE film elastic memory kple silicone PSA creep le nyaƒoɖeamenu/dzoxɔxɔ te. Mɔxexe ɖe enu: gradient winding tension (gotagome sesẽ, ememe loose) le ewɔwɔ me, tsɔ kpe ɖe asiɖeɖe le nutsyɔnu ŋu le akpa si meléna ɖe nu ŋu o. Dzrae ɖo ɖe -15°C va ɖo 40°C, 30-70% RH, le tsia dzi le agbawo dzi, trɔ agbalẽ xatsaxatsawo le ɣleti etɔ̃ ɖesiaɖe me. Ne èdi be yeakpɔ nusiwo wotsɔna léa nu ɖe ​​nu ŋu ƒe hatsotso siwo le ɣie la, tsɔ pepa si ɖea asi le eŋu kpe ɖe eŋu le ƒuƒoƒoawo dome.

PTFE dzoxɔxɔ gã ƒe kasɛt siwo wodzra ɖo ɖe agbalẽ xatsaxatsa ƒe nɔnɔme me ate ŋu akpe fu le interlayer adhesion (blocking) kple adhesive transfer yi non-stick akpa. Nusiwo gbɔ wòtso: PTFE film elastic memory kple silicone PSA creep le nyaƒoɖeamenu kple dzoxɔxɔ te. Egbɔkpɔnu: gradient winding tension – sesĩe le gotagome ƒuƒoƒo dzi, loose le ememe ƒuƒoƒo dzi – zã closed-loop tension control. Kpe ɖe eŋu kple asiɖeɖe le nu ŋu ƒe nutsyɔnu, nudzraɖoƒe nyuie (15-40°C, 30-70% RH), ɖoɖo ɖe tsia dzi, kple agbalẽ xatsaxatsa ƒe tɔtrɔ le ɣleti etɔ̃ ɖesiaɖe me.

Ele be PTFE ƒe dzoxɔxɔ gã ƒe kasɛt si wozãna le nuɖuɖu ƒe kadodo me nade bubu dzoxɔxɔ ƒe seɖoƒe sesẽwo ŋu: ≤260°C na zazã atraɖii (ɣeyiɣi aɖeke meli o), 260-300°C hena miniti 30 ko, eye wode se ɖe >300°C nu. Tepe la nye na kadodo si metso tẽ o ko (tray liners, heat sealer covers), ke menye nuɖuɖu babla tẽ o. Mègawɔ dɔ nuɖuɖu ƒe agba manɔmee gbeɖe o (dzoxɔxɔ ƒuƒu). Tsɔe ɖɔ li ne ʋuʋudedi, ɣie, alo vuvu.

Silicone pressure-sensitive adhesives (PSA) na PTFE dzoxɔxɔ gã ƒe kasɛtwo to vovo ŋutɔ le dzoxɔxɔ gã ƒe tsitsi ƒe dɔwɔwɔ me. Methylphenyl silicone PSA léa >85% ƒe lãgbalẽ ƒe ŋusẽ me ɖe asi le 250°C/ŋkeke 7 megbe, esime methyl ƒomevi si wozãna ɖaa ɖiɖina va ɖoa 50-70%. Addition-cured (hydrosilylation) systems naa liƒo nyuitɔ sã wu peroxide-cured. Ne èdi be yeawɔ dɔ le 200°C+ si yia edzi la, tia phenyl ƒe dzesi siwo wotsɔ kpe ɖe wo ŋu siwo woda gbe le.

Ele be dzoxɔxɔ ƒe PTFE pressure-sensitive adhesive (PSA) tapes nakplɔ dzoxɔxɔ esime wole ƒoƒom. Ne wotsɔ nusiwo wotsɔ yɔa nu me kpe ɖe eŋu la, enaa dzoxɔxɔ ƒe tsɔtsɔme nyona ɖe edzi gake egblẽa nu le nusiwo léna ɖe nu ŋu ŋu. Dadasɔ nyuitɔ zãa nu suesuesue siwo le dzogoe ene me siwo le ƒuƒuie (abe ƒunukpeƒe si kplɔa nu ene) siwo wotsɔ tsaka kple nusue suesuesuewo (be woatsɔ ayɔ teƒe siwo le ƒuƒlu me), si wɔnɛ be agba si wotsɔ yɔa nuawo katã me nɔa tsi si sina toa eme ƒe dzidzenua dzi vie. Ƒo asa na flakes kple fibers; wowua tack.