PTFE Tape Edge tihsan chhan

Views: 0 Author: Site Editor A chhuah hun: 2026-05-15 A chhuahna: Hmun

PTFE high temperature puan siamtu professional a nih angin, Jiangsu Aokai New Materials hian industry hriatna pawimawh tak tak a rawn share sak che a ni. PTFE high temperature tape-a edge warping leh falling off hi thil pakhat vang a ni lo va, mahse tape thlan dik loh, bonding surface condition tha lo, hnathawh dan dik lo leh service environment khauh tak takte inzawmkhawm avanga lo awm a ni. A hnuaia tarlan te hi hlawhchhamna chhan tlangpui leh a kaihhnawih solution te chu a ni:

PTFE High Temperature Tape avanga hlawhchhamna awm fo	Target hmanga chinfel dan tur
Adhesive backing dik lo thlan: Acrylic-based PTFE tape chu temperature sang taka hnathawhna hmuna hnawih a ni	120°C aia sang environment tan silicone adhesive backed PTFE tape thlang la; acrylic adhesive type hi temperature pangngai hmanna atan chauh hman theih a ni
Adhesive quality hniam zawk, viscosity hniam leh thermal stability tha lo	Lei hmain high-temperature performance test neih hmasak phawt a; thil siamtu hmingthang tak takte hnen atanga thil siam thlan chhuah a, an hot adhesion performance te enfiah thin
Bonding surface bawlhhlawh, oil stain, leivut, tui chhinchhiahna emaw residual old glue emaw hmanga khuh	A chunglam chu isopropyl alcohol emaw anhydrous ethanol emaw hmangin uluk takin silfai la, paste hmain a vawt kim vek ang; eng moisture pawh hian bonding effect a tichak lo ang
Mismatched surface roughness adhesive wetting tling thei lo	A hrual lutuk chu polish tha rawh; level rough surfaces emaw, 0.18-0.25mm thick PTFE tape hmanga gap awmte tihpun emaw a ni thei
Pasting kalphung dik lo: film tension lutuk, pressing leh air exhaust tling lo, temperature hniam taka siam emaw, repositioning repeated emaw	Lamination laiin tension tlemte hmang la, pressure roller hmangin nghet takin roll la, air bubbles te chu paih chhuak rawh; temperature hniam takah paste hmain surface te chu 20-25°C ah preheat hmasa phawt ang che; tape chu peeling leh re-stick loh tur
Temperature overload nasa tak: hun rei tak chhunga service 260°C aia sang emaw, temperature inthlak danglamna nasa tak emaw	260°C chhunga continuous operating temperature control, hun rei lote chhunga peak temperature 300°C aia tam lo leh minute 1 aia rei lo; temperature danglamna lian tham scenario atan silicone adhesive tape plus mechanical fixation hmang tangkai rawh
Substrate khauh lutuk leh thuk lutuk, curved emaw irregular surface-a fit theih loh	Conformability sang tak mamawh scenario tan thin-type PTFE tape 0.08-0.13mm chu dah pawimawh ber rawh
A dah dik loh chuan temperature sang, humidity leh ni êng direct hnuaiah adhesive aging hma lutuk a thlen thin	Tape sealed te chu hmun lum leh vawt takah -5~38°C leh humidity 30%~70%RH ah dah tur a ni

Edge warping tlem nei tape tan chuan warped parts chu roller hmangin local-in i press thei a, emergency hmanna atana adhesion tihpun nan 60°C hnuaiah boruak lum nem tak i hnawih thei bawk. Adhesive layer a chhiat chuan thlak leh re-pasting a ngai a ni.

Stable Bonding atana hman tur Standard Operation kaihhruaina

1. Lei chunglam Pre-treatment

Oil stain leh dust hian adhesive layer chu base surface atanga a then darh ang. A chunglam chu high-purity solvent hmangin phihfai la, a vawt kim vek tur a ni. Roller surface smooth-a roughening moderate hian adhesion nasa takin a ti tha thei a ni.

2. Key Lamination chungchang sawifiahna

Tape chu tension dik takin wind la; tension lutuk chuan shrinkage leh edge lifting chhunzawm zel a thlen ang.Fitting zawh veleh a tawp atanga a tawp thlengin a rualin roll la, air bubble zawng zawng a bo vek ang a, adhesive leh substrate inkarah full wetting a awm theih nan.Finish pasting in one go. Re-sticking hian original bonding strength chu nasa takin a ti tlem ang.

3. Environment leh Temperature Control

High-grade PTFE tape tan pawh safety temperature margin 20-30°C reserve rawh. Hun rei tak chhunga a lum lutuk chuan silicone adhesive chu chemical a tichhia ang a, a ti chhe thei a, hei hi a chhiat reng chhan ber a ni. Temperature inthlak fo hnuaiah clamp leh auxiliary fixing method dang hmang thin ang che. Chu bakah, alkali, ketone emaw ester solvent chak tak awmna hmuna hman a nih chuan tape-te chemical resistance chu nemnghet rawh; silicone adhesive backed tapes hian comprehensive compatibility tha zawk a nei a ni.

A tawi zawngin, edge lifting leh peeling chungchanga harsatna chinfelna chu a bulpui berah chuan product thlan dik, standardized construction leh strict working condition control-ah a innghat a ni. Service temperature tak tak ang zela adhesive backing tha thlan hi PTFE high temperature tape te stable application atana core guarantee a ni.

He thuziak hi a rawn pe a ni Jiangsu Aokai thil thar siam chhuahna Co., Ltd.

PTFE high temperature fabric, PTFE high temperature tape, PTFE high temperature mesh belt, seamless fusing machine belt, single-sided PTFE puan, high temperature resistant conveyor belt leh high temperature resistant fiberglass cloth te bakah kan product hrang hrangte tana detailed parameters, application instructions leh customized solutions i mamawh chuan min rawn biak theih reng e:

· Pu Guo: +86 18944819998 zawhfiah theih a ni

· Pu Liu: +86 13705266308 ah zawhfiah theih a ni

Professionalism leh integrity service tenet kan vawng nung reng a, thinlung zawng zawngin one-stop industrial solution leh ngaihtuahna senga service kan pe che u a ni.