PTFE ƒe dzoxɔxɔ gã ƒe adhesive tape ƒe creep tsitretsitsi le ɣeyiɣi didi ƒe agba madzudzɔmadzudzɔe te (vevietɔ le 200-260°C) la, wotsɔa nu eve dea dzesii: silicone PSA crosslink density (crosslinking si lolo wu xea mɔ na sisi) kple substrate ƒomevi (fiberglass-reinforced PTFE tsi tre ɖe cold creep ŋu; pure PTFE film creepps). Aŋe si wometsɔ ka blae o la doa kpo nu kabakaba ne dzoxɔxɔ sesẽ. Nusiwo wotsɔna léa nu ɖe ​​nu ŋu siwo le kpekpem wu dzia afɔku si le ʋuʋu me ɖe edzi.

Le PTFE dzoxɔxɔ gã tape si wozãna le abrasive sliding friction dɔwɔwɔwo, dzidzenu non-stick kple dzoxɔxɔ tsitretsitsi mesɔ gbɔ o. Tiatia ƒe dzidzenu veviwo: Taber ƒe abrasion ƒe bu (<15 mg/1000 cycles), PTFE ƒe nutsyɔnu si woɖɔli si yɔ fũ (carbon/graphite/MoS2), PV seɖoƒe ŋuti nyatakakawo, substrate ƒe ŋusẽ (≥200 N/cm), kple mating surface roughness (Ra 0.2-0.4 μm). Nugbɔ takpɔkpɔ nyuie kple eƒe kadodo blibo le vevie ŋutɔ na agbenɔƒe didi.

PTFE substrate nye nusi te ŋu nɔa te ɖe dze sisi nu le dzɔdzɔme nu (tsi ƒe xɔxlɔ̃ <0.01%). Ke hã, tape ƒe dɔwɔwɔ bliboa nɔ te ɖe adhesive ƒomevi dzi: silicone PSA te ŋu nɔa te ɖe ƒumelãwo ƒe nɔnɔmewo nu (500-1000h dze sisi dodokpɔwo,>80% peel retention); acrylic PSA do kpo nu. Atikewɔwɔ nyuie le anyigba dzi, kuɖɔ manɔmee, kple nutrenu nutrenu kple silicone nutrenu le vevie ŋutɔ na kakaɖedzi ɣeyiɣi didi le ƒuta nuƒolanɔƒewo kple tɔdziʋuwo.

PTFE fiberglass tape hiã dedienɔnɔ ŋuti ɖaseɖigbalẽ vevi etɔ̃: UL (elektrik kple dzo ƒe dedienɔnɔ), FDA (nuɖuɖu ƒe kadodo ƒe sedziwɔwɔ), kple ISO 9001:2015 (nyonyo dzi kpɔkpɔ). Kasɛt siwo ŋu woɖo kpee naa dɔwɔwɔ ɣesiaɣi, woƒe agbenɔƒe didi wu, eye ga si wozãna ɖe wo tɔ ta katã dzi ɖena kpɔtɔna togbɔ be ga si wozãna do ŋgɔ la lolo wu hã. Kpɔ ɖaseɖigbalẽwo dzi tẽ ɣesiaɣi kple dɔwɔƒe siwo naa ɖaseɖigbalẽwo.

Wozãa PTFE ƒe dzoxɔxɔ gã ƒe kasɛt le atikewɔwɔ ƒe dɔwɔwɔ ƒe akpa etɔ̃ me: dɔlékuiwutikewo takpɔkpɔ (autoclave trays, heat-seal packaging), dɔwɔnu ƒe anyigba dzi dɔdamɔnu (low-friction coating, electrical insulation), kple mɔ̃ siwo woate ŋu ade ame me (vascular grafts, sutures). Woto ISO 10993 dzi ɖo kpe nugbagbewo ƒe ɖekawɔwɔ dzi, eye FDA 21 CFR 177.1550 ɖo gɔmeɖoanyi nuwo ƒe dedienɔnɔ anyi.

PTFE ƒe dzoxɔxɔ gã ƒe tape mete ŋu nɔa te ɖe keklẽŋusẽ si nye ionizing radiation nu nyuie o. Le gamma 1 kGy ko me la, tensile ŋusẽ ɖiɖina va ɖoa ~25% le gbãtɔ me. Esɔ na nuto siwo me womezãa atike suewo le o (nuɖuɖu/atikewɔwɔ me vidzidzi <10 kGy) ko. Le nuklia dɔwɔƒewo alo yamenutomeyimɔ̃wo gome la, zã polyimide alo PEEK ɖe eteƒe.

Le PTFE ƒe dzoxɔxɔ gã ƒe kasɛtwo gome le nyɔnyrɔ ɖe tsi me ɣeyiɣi didi me la, PTFE ƒe gɔmeɖoanyia gakpɔtɔ nyea atike si mewɔa dɔ o, gake nusi léna ɖe nu ŋu lae nye nusi gbɔdzɔ. Tsi gbɔdzɔa silicone PSA; dzetsi naa xɔxlɔ̃ kabakaba. Le atike sesẽwo gome la, fluorosilicone alo perfluoropolyether adhesives – alo PTFE tape si me aŋɔ mele o – hiã. Peel ƒe ŋusẽ bu va ɖo 40% le gaƒoƒo 48 le tsi me megbe.

Ele be PTFE ƒe dzoxɔxɔ gã ƒe kasɛt si wozãna le nuɖuɖu ƒe kadododɔwo me nanɔ dzoxɔxɔ ƒe seɖoƒe si woɖo me: ≤260°C na zazã atraɖii, ≤300°C na eƒe kɔkɔƒe kpuiwo (aɖabaƒoƒo), eye gbeɖe wu 327°C (gbegblẽ). FDA kple EU ƒe sewo megblɔ ɣeyiɣi si woɖo ɖi na xexeame katã o – ɣeyiɣi didi si woatsɔ aƒo ka na ame le dedie nɔ te ɖe dzoxɔxɔ dzi eye ele be woaɖo kpe edzi to ʋuʋu ƒe dodokpɔ siwo srɔ̃a nɔnɔme ŋutɔŋutɔwo me.

PTFE ƒe dzoxɔxɔ gã ƒe kasɛt nyuitɔ tiatia na 3D agbalẽtamɔ̃ ƒe aba dzodzoe bia be woalé fɔ ɖe dzesi vevi ene ŋu: dzoxɔxɔ ƒe tsitretsitsi (vaseɖe 260°C +), nusi wotsɔ fiberglass do ŋusẽe (0.18mm nyuitɔ), silicone adhesive backing kple non-stick etame, kple kekeme/mɔɖeɖe ɖe nu ŋu nyuie. Mɔfiame sia kpena ɖe ŋuwò be màƒo asa na ʋuʋudedi, nusiwo susɔ, kple agbalẽtata ƒe kpododonu.

Glass ƒe tɔtrɔ ƒe dzoxɔxɔ (Tg) si le silicone ƒe nyaƒoɖeamenu-sensitive adhesive me anɔ abe -120°C – si bɔbɔ kura wu acrylic adhesives. Tg sia si bɔbɔ ŋutɔ la nana PTFE ƒe dzoxɔxɔ gã ƒe kasɛt nɔa te sesĩe eye wòléna ɖe nu ŋu le -70°C gɔ̃ hã, si xea mɔ na gbagbãƒe ƒe gbagbã eye wònaa woate ŋu alé ɖe nu ŋu si ŋu kakaɖedzi le le cryogenic dɔwɔwɔwo me.