Aƒeme » Nyadzɔdzɔ » PTFE ƒe Adhesive Tape » PTFE Tape na Abrasion-Tsitretsitsi Sliding Friction: 5 Vevi siwo ŋu woabu

PTFE Tape na Abrasion-Tsitretsitsi Sliding Friction: 5 Vevi siwo ŋu woabu

Views: 0 Author: Site Editor Ɣeyiɣi si Wotae: 2026-06-02 Dzɔtsoƒe: Teƒe

PTFE xɔ ŋkɔ le eƒe friction coefficient si bɔbɔ (0.05-0.10) ta. Gake ɣekaɣie Wozãa PTFE dzoxɔxɔ gã ƒe tape le glidzaglidza friction dɔwɔwɔwo me – abe mɔfiame ketekemɔwo, wear strips, chute liners, alo sliding seals – friction ɖeɖe mesɔ gbɔ o. Kuxia ŋutɔŋutɔe nye tsitretsitsi ɖe abrasion ŋu.

Ne wometiae nyuie o la, PTFE ƒe nutsyɔnu la vuvuna le kwasiɖa geɖe me, si wɔnɛ be fiberglass ƒe anyigba la dzena eye wònana wòdoa kpo nu vevie. Wometrɔ asi le standard non-stick tape ŋu na dynamic sliding contact o.

Aokai PTFE to PTFE kasɛt siwo te ŋu dona le wo ŋu vɛ na dɔ sesẽ siwo wowɔna le glidzaglidza me. Mɔfiame sia ƒo nu tso nu vevi atɔ̃ siwo ŋu woabu ŋu: abrasion resistance metrics, coating quality, dzoxɔxɔ ƒe liƒo, adhesive ƒe dɔwɔwɔ, kple eɖoɖo ƒe mɔnuwo.

Dɔwɔwɔ ƒe Dzesi Vevi Siwo Ŋu Woaɖo Akpɔ

1. Abrasion Tsitretsitsi – Nu Vevitɔ Parameter

Dodokpɔmɔnu	Dzidzenu	Asixɔxɔ si Wozãna (Standard PTFE) .	Taɖodzinu na Tepe si Tsi Tre Ðe Wo Ŋu
Taber Abrasion Bu (ASTM D4060, CS-17 tasiaɖamfɔ, 1000g agba)	mg/1000 ƒe tsatsam	Ame alafa geɖe ƒe mg	<15 mg (si sɔ gbɔ wu: <5 mg) .
Dynamic Coefficient of Friction ƒe xexlẽdzesi	μ	0.05-0.10 le gɔmedzedzea me	Li ke 0.05-0.15 le agbe me
PV Seɖoƒe (Nyaƒoɖeamenu × Duƒuƒu) .	Pa·m/s alo psi·fpm	Eto vovo le alesi wowɔe nu	Xɔe tso nudzrala gbɔ

Nusita Taber ƒe abrasion le vevie: PTFE ƒe nutsyɔnu dzadzɛ la vuvuna kabakaba le glidzaglidza ƒe kadodo me. PTFE si ŋu wotrɔ asi le si wotsɔ yɔ fũu (si me carbon fiber, graphite, MoS2, alo glass fiber le) ɖea eƒe vuvu dzi kpɔtɔna ŋutɔ. Premium wear-resistant tape ateŋu aɖo <5 mg ƒe bu le 1000 ƒe tsatsam ɖesiaɖe me – 20-50x nyo wu PTFE si womeyɔ o.

PV seɖoƒe si woɖe fia: Nusi woɖe mɔ na si sɔ gbɔ wu tso kadodo ƒe Nyaƒoɖeamenu (P) kple sliding Velocity (V) me. Seɖoƒe sia dzi ɖeɖe kpɔtɔ nana wòvuvu kabakaba, dzoxɔxɔa nu sẽna, alo nusi wotsɔ blae la me gblẽna. Bia PV curves tso wò nudzrala gbɔ ɣesiaɣi.

Aokai PTFE naa tepe ƒe dzesi siwo te ŋu nɔa te ɖe vuvu nu kple Taber abrasion ƒe bu le 10 mg/1000 ƒe tsatsam te – si ŋu woɖo kpee to ASTM D4060 dodokpɔ si le eɖokui si me. Míaƒe atike si me carbon-fiber yɔ fũu la nana μ nɔa anyi 0.15 le tsatsam 10,000 megbe gɔ̃ hã.

Taber-Abrasion-Dodokpɔ-Emetsonuwo-Sɔsɔ-Bar-Chart.png

2. Coating Quality & Substrate Xɔtutu

Parameter (Parameter) ƒe nɔnɔmetata	Kafukafunya	Nu ka ta
Nusi wotsɔ blaa nu ƒe titrime (dɔwɔwɔ ƒe anyigba) .	≥0.05 mm (0.08-0.15 mm na awudodo sesẽ)	Nusi wotsɔ blaa nu si le kpekpem wu nana be eƒe awudodo nɔa anyi didi wu
Nusi wotsɔ blaa nu ƒe ƒomevi	PTFE si ŋu wotrɔ asi le si yɔ fũ (carbon, graphite, MoS2, glass fiber) .	Far superior abrasion tsitretsitsi vs. womeyɔ o
Nutsyɔtsyɔ ƒe blibonyenye	Pinholes aɖeke meli o, sintered bliboe	Exea mɔ na fiberglass ƒe dodo kaba
Base avɔ tensile ŋusẽ	≥200 N/cm ƒe didime	Tsi tre ɖe keke le shear friction te ŋu
Weave ƒomevi	Awu gbadza alo satin si ŋu ŋusẽ le ŋutɔ	Aramid avɔ na agba siwo gbɔ eme

3. Dzoxɔxɔ ƒe Tsitretsitsi & Dzoxɔxɔ ƒe Liƒo

Subɔsubɔdɔ ƒe dzoxɔxɔ si yia edzi naɖo dɔwɔwɔ ƒe nudidi gbɔ (zi geɖe la, ≥260°C) .
Nusi wotsɔ blaa nu sesĩe alo aŋe kabakaba le dzoxɔxɔ sesẽ me aɖeke meli o
Le dzoxɔxɔ ƒe tsitsi le 250°C hena gaƒoƒo 100 megbe la, tensile strength kple abrasion performance ƒe gbegblẽ mele be wòawu 20% o .

4. Adhesive Layer Dɔwɔwɔ (Na Ðokuisi-Adhesive Tapes) .

Adhesive Ƒomevi	Dzoxɔxɔ ƒe Tsitretsitsi	Tsitretsitsi ɖe Creep ŋu	Alesi wòsɔ na Sliding
Silicone PSA ƒe dɔwɔwɔ	≤260°C ƒe dzoxɔxɔ	Enyo kple crosslinking nyuie	Tiatia vevitɔ
PSA si wotsɔ akrilik wɔe	≤150°C ƒe dzoxɔxɔ	Ame dahe le dzoxɔxɔ te	Womekafui na ʋuʋudedi si ƒe dzoxɔxɔ nu sẽ o
Primer + silikɔ si wotsɔna ƒoa nu	≤260°C ƒe dzoxɔxɔ	Enyo ŋutᴐ	Le anyigbadzinu siwo ƒe ŋusẽ mede o gome (le kpɔɖeŋu me, gakpo si mexɔ dzo o) .

De dzesii: Le agba kpekpe ƒe ʋuʋu ƒe dɔwɔwɔ siwo me kasɛt la le ʋuʋudedi ƒe nuteɖeamedzi si yia edzi te la, bu mɔ̃ ƒe babla (rivets, clamping strips) tsɔ kpe ɖe adhesive ŋu.

5. Anyigba ƒe Nɔnɔme & Titrime Ðekawɔwɔ

Anyigba ƒe nɔnɔme: Nuŋɔŋlɔ sue aɖe kpena ɖe ame ŋu be nu nyui siwo vuvu ƒe gbeɖuɖɔwo nɔa anyi, si xea mɔ na coefficient spikes alo plough-type abrasive wear si nusuekpɔmɔ̃ siwo ƒo ƒu hena vɛ.
Titrime ƒe mɔɖeɖe: Wokpɔa titrime bliboa dzi le ±0.02 mm me le agbalẽ xatsaxatsa bliboa katã dzi be woakpɔ egbɔ be wotsɔ tsi si wotsɔ ƒua tsii la de eme eye woaƒo asa na teƒea ƒe gbagbã kaba.

Optimization Solutions na High-Wear Sliding Nɔnɔmewo

1. Nusiwo Wozãna ƒe Tɔtrɔ

Tɔtrɔwɔwɔ le eŋu	Ƒe dᴐwᴐna	Nyuitɔ Kekeake Na
Carbon fiber ƒe nusi wotsɔ yɔa nu me	Enaa abrasion tsitretsitsi nyona ɖe edzi, dzia μ ɖe edzi vie	Agba gã, ʋuʋudedi si ƒe duƒuƒu sue
Graphite-nu si wotsɔ yɔa nu me	Eɖea friction dzi kpɔtɔna, eƒe awudodo ƒe nyonyo le mɔ si sɔ nu	Dɔwɔwɔ siwo zɔna kabakaba, siwo me agba mele o
Glass fiber si wotsɔ yɔa nu me	Dzia sesẽme kple eƒe vuvu ƒe tsitretsitsi ɖe edzi	Agba si sɔ, abrasive nɔnɔmewo
MoS2 ƒe nusi wotsɔ yɔa nu me	Ami nyuitɔ kekeake, tsitretsitsi ɖe eƒe vuvu ŋu nyuie	Liƒo dzi amisisi ƒe nɔnɔmewo
PEEK ƒe atikekui si wotsɔ yɔa nu me	Tsitretsitsi ɖe nudodo ŋu si de ŋgɔ wu, gazazã si lolo wu	Nɔnɔme siwo me ʋuʋudedi le si gbɔ eme
Aramid/carbon avɔ ƒe anyigba	Eɖɔlia fiberglass hena ŋusẽ si lolo wu	Agba kpekpe, lãɖeɖe gã

2. Srɔ̃ɖeɖe ƒe Sɔlemehawo ƒe Sɔsɔ

Parameter (Parameter) ƒe nɔnɔmetata	Kafukafunya	Nu ka ta
Nusiwo sɔ kple wo nɔewo ƒe ƒuƒuiƒe (Ra) .	0.2 – 0.4 μm ƒe didime	Gbeɖiɖi akpa (Ra>0.8) → lã PTFE; wòle gbadzaa akpa (Ra<0.1) → gbeɖuɖɔ aɖeke meléna ɖe te o
Nya siwo sɔ kple wo nɔewo	Ga si mexɔ dzo o, chrome sesẽ si wotsɔ blae, aluminum sesẽ si wotsɔ anodized wɔe	Ƒo asa na gayibɔ si me mekɔ o (graphite si wotsɔ dea PTFE me femaxee) .
Mɔxexe ɖe nusue sesẽwo nu	Ke ƒe xɔ, dzadzɛnyenye edziedzi	Nusuekpɔmɔ̃ siwo wotsɔ de eme la hea abrasive vuvu vevie
Amisisi ƒuƒu si kpena ɖe ame ŋu	PTFE alo fluorine-based dry lube (si me ɖiƒoƒo mele o, si te ŋu nɔa te ɖe dzoxɔxɔ gã nu) .	Eɖea ʋuʋudedi kple dzoxɔxɔ ƒe ƒuƒoƒo dzi kpɔtɔna

Mating-Anyigba-Kɔme-vs-Wear-Rate-Graph.png

3. Ðoɖowɔwɔ & Xɔtuɖaŋu ƒe Aɖaŋuɖoɖowo

Dzidze	Dɔwɔwɔ	Viɖe
Edge takpɔkpɔ	Ðo goawo ɖe friction zone godo; tsɔ ga si wotsɔ blaa nu ɖe wo nɔewo ŋu lée ɖe te alo tsɔe de afɔɖeɖe ƒe dowo me; mɔ̃ chamfer/goglo nugbɔ le mating akpa	Eɖea ʋuʋudedi si le abe aŋe ene ɖa
Kadodo blibo	Degrease kple roughen base (blast va ɖo Sa2.5); mia tape nyuie be ya nado goe; ne agba kpekpe la, tsɔ nusi wotsɔna léa nu ɖe nu ŋu kple mɔ̃ si wotsɔ blaa nu ɖekae	Exea mɔ na ya ƒe ʋuʋu kple ya ƒe gege ɖe teƒea
Modular ƒe nɔnɔme si woate ŋu aɖɔli	De tape ɖe slider/subplate si woate ŋu aɖe ɖa dzi	Ebɔbɔ ɣeaɖewoɣi ɖɔliɖɔli, kpɔa dɔwɔnuwo ƒe pɛpɛpɛ ta

Nyataƒoƒo – Tiatia ƒe Gɔmeɖose Vevi Etɔ̃

Le abrasion-focused sliding scenarios gome la, tsɔe ɖo nɔƒe gbãtɔ:

PTFE ƒe nutsyɔnu si woɖɔli si woyɔ – Carbon fiber, graphite, MoS2, alo glass fiber filler na Taber ƒe abrasion tsitretsitsi nyona ɖe edzi ŋutɔ (taɖodzinu <15 mg/1000 tsatsam, anyo wu be <5 mg).
Substrate si ƒe ŋusẽ lolo – Fiberglass si ƒe tensile strength ≥200 N/cm, alo aramid/carbon fabric na agba siwo gbɔ eme.
Wokpɔ ŋusẽ ɖe counterpart surface roughness dzi – Lé Ra 0.2-0.4 μm me ɖe asi, zã gakpo si mexɔ dzo o alo chrome sesẽ.

Nudidi bubuwo:

Bia Taber abrasion data kple PV seɖoƒewo tso nudzralawo gbɔ.
Dee kple nugbɔ takpɔnu (clamping strips, groove embedding, chamfered mating akpawo).
Ne agba kpekpewo le ʋuʋum atraɖii la, tsɔ nusi léna ɖe nu ŋu kple mɔ̃ si wotsɔ blaa nu la tsaka.
Aɖaŋuwɔwɔ na modular ɖɔliɖɔli le afisi wòanya wɔ le.

Sliding-Friction-Dɔwɔwɔ-Dɔwɔwɔ-Nɔnɔmetata.png

Kpuie ko la, tiatia PTFE dzoxɔxɔ gã tape na abrasive sliding friction dɔwɔwɔwo bia be woayi ŋgɔ wu standard non-stick kple dzoxɔxɔ specs. Lé fɔ ɖe Taber ƒe abrasion ƒe bu (<15 mg/1000 cycles), nutsyɔnu si woɖɔli si yɔ fũu, substrate tensile strength (≥200 N/cm), kple mating surface roughness (Ra 0.2-0.4 μm) ŋu. Nugbɔ takpɔkpɔ nyuie, kadodo blibo, kple modular design didi subɔsubɔ ƒe agbenɔƒe ɖe edzi ŋutɔ.

Ƒo asa na PTFE tape si womeyɔ o hena dynamic sliding contact – avuvu to eme kabakaba. Ke boŋ gblɔ dzesi siwo te ŋu nɔa te ɖe vuvu nu kple abrasion ŋuti nyatakaka siwo ŋu woda asi ɖo.

Èhiã PTFE kasɛt si mete ŋu doa o na wò sliding dɔwɔwɔa? Aokai PTFE naa carbon-fiber, graphite, kple MoS2-yɔ fũ ƒe dzesiwo kple Taber ƒe abrasion ƒe bu le 10 mg/1000 ƒe tsatsam te. Te ɖe mía ŋu kple wò nyaƒoɖeamenu, duƒuƒu, kple wò kpeɖeŋutɔ nu hena aɖaŋuɖoɖo.

Nyatakaka Siwo Na Jiangsu Aokai Nu Yeyewo Mɔ̃ɖaŋununya Co., Ltd.

Ne èdi nyatakaka tsitotsito, dɔwɔwɔ ƒe aɖaŋuɖoɖo, kple egbɔkpɔnu siwo wowɔ ɖe ɖoɖo nu siwo ƒo nu tso PTFE dzoxɔxɔ gã avɔ, PTFE adhesive tape, PTFE mesh alidziblanu, seamless fuser alidziblanu, ɖeka-afã PTFE coated avɔ, dzoxɔxɔ-tsi tre ɖe conveyor belt kple dzoxɔxɔ gã fiberglass avɔ , taflatse te ɖe mía ŋu:

Aƒetɔ Guo: +86 18944819998
Aƒetɔ Liu: +86 13705266308

Míeléa dɔwɔwɔ kple fɔmaɖimaɖi me ɖe asi be míatsɔ egbɔkpɔnu siwo wowɔ ɖe ɖoɖo nu siwo katã le ɖeka me kple nudzadzra megbe subɔsubɔdɔ si me woléa ŋku ɖo la ana.