Plastic Injection & Extrusion Demolding-ah hian PTFE Tape leh PTFE Coating te hi a awm a

Views: 0 Author: Site Editor A chhuah hun: 2026-04-21 A chhuahna: Hmun

PTFE high-temperature tape siamtu Jiangsu Aokai New Materials chuan injection molding leh extrusion demolding-a spray coating nena khaikhin chuan PTFE tape hman thatna leh that lohna a sawifiah a.

On-site solution angin PTFE high-temperature tape hian core value a pe a, chu chu flexibility leh low cost a ni.

Instant Demolding & Hnathawh danah pawh a inthlak danglam thei

PTFE high-temperature tape hian professional spraying equipment a mamawh lo — release liner phel-in direct-a hnawih theih a ni. Extrusion rollers emaw injection mold parting surface-a mold a lo stick nghal a nih chuan PTFE tape chauh hi in-line repair without shutdown .Chu danglamna chu spray coating process-ah hian mold disassembly leh off-site treatment a ngai a, hei hian ni engemaw zat a daih thei.

Small Batch Production atan Economic Advantage neih a ni

Small batch trial production emaw mold validation atan chuan PTFE tape roll khat man hi a hniam hle a, PTFE spray coating erawh chuan minimum order quantities sang tak leh upfront preparation costs a nei sang hle thung.PTFE tape hian process engineer te chu surface modification test te chu sunk costs hniam tak tak nen an ti thei a ni.

Wide Process nena inmil theihna

PTFE high-temperature tape hi a tlangpuiin fiberglass puan PTFE-a impregnated a ni a, 260°C thlenga lumna do chhunzawm zel a ni — PP, PE, ABS, PA, etc. telin general purpose plastic tam zawk tan a tawk.A smooth surface hian 0.05 leh 0.1 inkar friction coefficient nghet tak a nei a, extrusion die-a material buildup chu a titawp thei hle hawnna a awm.

Hun eng emaw chen atana Mold laka invenna

Mould testing neih lai emaw, maintenance zawhah emaw, PTFE tape hman hian mold steel chunglam chu molten plastic-in a tihchhiat hmasak loh nan a veng tha hle a, a bik takin flame retardant emaw glass fiber reinforced emaw molding a nih chuan materials.Disposable consumable layer angin tape chu phelh theih a ni a, mold chunglam chu a fai a, a awm reng thei bawk.

PTFE tape hi a awlsam hle laiin, long term industrial production-ah chuan physical limitation a nei a ni.A hnuaia tarlan te hi PTFE high-temperature tape leh PTFE spray coating te performance danglamna pawimawh tak takte khaikhin a ni.

表格 tih a ni

Inthlauhna Item	PTFE High-Temperature Tape (Core Solution) hmanga siam chhuah a ni.	PTFE Spray Coating (Alternative Solution) hmanga siam chhuah a ni.
Dilna kalpui dan tur	Site-ah kut hmanga hman theih a ni a; mold disassembly a ngai lo.	Sandblasting leh high temperature sintering a ngai a; tihdanglam theih loh process.
Demolding-a rawngbawlna nun	A tlangpuiin thlak hmain molding cycle 60–200 vel a daih.	Hard coating hian cycle sang tam tak atanga sang tam tak a daih thei.
Dimensional Accuracy-a nghawng a neih dan	A thuk zawng chu 0.08–0.25 mm a ni a, hei hian part dimension a tidanglam thei.	Coating te tak te (20–50 μm), precision tolerances-ah nghawng a nei lo.
Complex Geometry hmanga insiamrem theihna	Flat surface leh radius rollers lian tak tak tan chauh a tha; ribs thuk tak nen a inmil thei lo.	Uniform takin complex cavities, slides, leh undercuts te a khuh vek.
Edge Buildup a awm theihna tur risk	Resin hmin chu seam-ah a lut thei a, tihfai fo a ngai a ni.	Seamless, one piece surface a ni a, buildup atan dead zone a awm lo.

Demolding Performance tichiangtu thil pawimawh tak takte

· .

Surface Preparation is Critical PTFE tape i hnawih hmain oil, residual release agent, leh mold surface atanga oxidation te chu acetone emaw alcohol emaw hmangin uluk takin silfai thin ang che. Dust particle te tak te pawhin blistering a siam thei a, chu chuan high temperature melt avanga tearing a thlen thei bawk.

· .

Seam Treatment Roller wrapping emaw, flat surface inzawm emaw hian gap hi a pianphungah a awm thin. Melt penetration leh edge lifting ven nan melt flow direction-a overlapping a tha zawk. butt joining ai chuan

· .

Thermal Conductivity Effect PTFE tape-a fiberglass layer hian thermal insulation tlem a pe a. Thin wall, high speed injection molding atan chuan hei hian mold temperature response time chu tlem a tihtlem thei a, cycle chu second 1–2 chhungin a ti sei thei bawk — PTFE tape hman man thup a ni.

· .

A chunga kan tarlan te hi Jiangsu Aokai New Materials Technology Co., Ltd.

Parameters chipchiar tak tak, application scenarios, leh kan product range zawng zawng tana customized solutions — PTFE high temperature puan, PTFE high temperature tape, PTFE high temperature mesh belt, bonding machine tan seamless belt, single sided PTFE puan, high temperature resistant conveyor belt, high temperature fiberglass puan, leh thil dang tam tak te pawh a tel — min rawn biak theih reng e:

· Service Hotline:Mr. Guo: 18944819998 Pu Liu: 13705266308 A rilru a hah lutuk chuan a rilru a buai em em a

Professional leh rinawm service philosophy kan vawng nung a, one stop solutions leh attentive service pe turin kan inpe a ni!