Sengoliloeng sena se qaqisa ts'ebeliso ea lesela la fiberglass e koahetsoeng ke PTFE indastering ea elektroniki le ea motlakase. Libaka tse tšeletseng tse kholo: Insulation le tšireletso ea mocheso o phahameng - motlakase inter-turn/slot/ phase insulation, transformer layer insulation, coil wrapping, ho itšehla thajana ha lisebelisoa tsa motlakase; Copper-clad laminate le PCB tlhahiso - ho lokolla lesela ka PCB lamination, prepreg le CCL e hloekileng conveying; Electronic soldering - masking solder bakeng sa wave/reflow soldering (ts'ireletso ea menoana ea khauta), mabanta a conveyor a ontong a phallang, limmete tsa ho sebetsa tsa soldering, likoahelo tse sireletsang lithunya tsa moea o chesang; Lithapo tsa lithapo le lithapo - theipi e koahelang mocheso o phahameng oa mocheso, matsoho a futhumetseng le likoahelo tse sa cheng, mabanta a ho tsamaisa li-tubing a fokotsa mocheso; Anti-static le hloekile - mabanta a conveyor kamoreng e hloekileng le limmete tsa mosebetsi, semiconductor le photovoltaic high-themperature e fetisang.

Sengoliloeng sena se fana ka mekhoa ea tlhahlobo ea thepa e khahlanong le ho khomarela le ho hloekisa habonolo ea lesela la fiberglass e koahetsoeng ke PTFE khahlano le matheba a oli le lerōle. Mekhoa e kenyelletsa: Teko ea ho kopana le matla a holim'a metsi - metsi a kopanang le metsi ka tloaelo>110 °, rolling angle越小越好, matla a holim'a metsi hantle 18-20 mN/m; Teko ea lekhapetla la mochini - matla a peel a 180 ° ka tepi e tloaelehileng, e loketseng <0.1 N/25 mm; Liteko tsa ho hanyetsa oli tse ts'oanelang - mokhoa oa ho thella oa mafura / mokhoa oa ho sala, mokhoa o lekaneng oa ho hlakola ho hloekisa ho sebelisa phapang ea mebala ΔE tekanyo (e nyenyane ΔE = ho hloekisa hantle), le tlhahlobo e potlakileng ea letšoao la oli (ho fokotseha ha enke ho bontša ho thibela ho silafatsa); Teko e khahlanong le lerōle - mokhoa oa ho lokisa lerōle ka tlhahlobo ea setšoantšo, ho tlosoa ha lerōle la moea ho lekanya lebelo le fokolang la ho phatloha, le tlhahlobo ea adsorption ea electrostatic ka ho hanyetsa holim'a metsi; Tlhahlobo ea nako e telele - pheta liteko tsohle ka mor'a botsofali bo phahameng ba mocheso (260°C/300°C) kapa Taber abrasion ho netefatsa botsitso ba nako e telele ea ts'ebetso.

Sengoliloeng sena se akaretsa lits'ebetso tsa lesela la mocheso o phahameng oa Teflon (PTFE-coated fiberglass fabric) lebaleng la sefofane. Libaka tse ka sehloohong tsa ts'ebeliso: Ho etsa thepa e entsoeng ka motsoako - ho lokolla lesela / filimi ka ho bopa ha autoclave, likarolo tsa ho itšehla thajana, mabanta a mocheso o phahameng oa mocheso bakeng sa tlhahiso ea prepreg; Tšireletso ea mocheso oa enjene le mocheso o phahameng - likobo tse thibelang mocheso, li-firewall cladding, lihokelo tse feto-fetohang tsa mocheso o phahameng; Tšireletso ea motlakase le ts'ireletso ea lithapo - ho phuthela ha cable ka likamoreng tsa enjene le libaka tsa lisebelisoa tsa ho lulisa; Bokahare ba lifofane le tšireletso ea mollo - likharetene tsa mollo / litšitiso tsa mosi tse finyellang litekanyetso tsa FST, ho roala kobo ea ho futhumatsa mocheso / acoustic; Lisebelisoa tsa sebaka le sepakapaka - likopano tse nang le li-multi-layer insulation (MLI), li-anti-cold-weld lubrication liner bakeng sa mekhoa ea ho tsamaisa lisebelisoa tsa letsatsi le li-antenna, lesela la ho laola mocheso.

Sengoliloeng sena se hlalosa hore na PTFE e tlama joang ho substrate ea lesela la fiberglass ka lesela la mocheso o phahameng oa Teflon. Ho kopanya lik'hemik'hale ka kotloloho ha ho khonehe ka lebaka la matla a holimo a tlase a PTFE. Ho kopanya ho finyelloa ka: Mechanical interlocking ('mele tlamahano) - PTFE emulsion phunyeletse likheo faeba le ho tšoara likhoele tsa fiber ka mor'a hore sintering; Silane coupling agent pretreatment - e theha borokho ba limolek'hule lipakeng tsa likhoele tsa khalase tse sa tsitsang le organic primer; Lik'hemik'hale primer transition layer - ho sebelisa li-resin tsa PAI, PPS, PES kapa PEEK tse nang le PTFE micropowder, tse sebelisoang ka mor'a ho kopanya phekolo ho theha lera le matla la phetoho; Lamination ea filimi e khomarelang e chesang e chesang - FEP kapa PFA lifilimi (ntlha e qhibilihisang 260-310 ° C) e kopanya lifilimi tsa PTFE tse entsoeng pele ho lesela; Sebopeho sa gradient ka li-multiple impregnation le sintering cycles - hlapolla pase ea pele e nang le se tlamang / se kopanyang e kenella ka hare ho likhoele, e lateloe ke ho kenngoa ha PTFE, ho theha sebopeho sa gradient ho tloha fiberglass ho ea PTFE e hloekileng.

Sengoliloeng sena se bua ka mokhoa oo moralo oa sebopeho sa microporous oa Teflon e phefumolohang (PTFE) e nang le mocheso o phahameng oa mocheso o lekanyang ho kenella ha moea ka ho kenella le thepa e sa tsitsang. Khohlano ea mantlha: ho kenella ha moea ho hloka li-pores tse bulehileng, athe ho kenella ka hare ho hloka hore ho be le ho teteana le ho se thupa ho hloka libaka tse boreleli. Mekhoa e leka-lekaneng ea moralo: ho laola bophara ba pore ka karolelano (0.1-2μm, hantle <0.5μm) ho thibela ho kenella ha qhibiliha le ho boloka matla a ho senya; laola porosity ho 50-70% (≈60% optimal) ho finyella Gurley 20-100s / 100cc le matla a dielectric ≥2kV bakeng sa filimi ea 0.13mm; amohela sebopeho sa pore sa marang-rang sa 3D se phahameng sa tortuosity (τ≈2.5-4) ho hatella likanale tse otlolohileng tsa ho lahla; haha ​​pore asymmetric gradient pore le lera le teteaneng la holim'a letlalo (1-5μm) bakeng sa ho se thunye / insulation le hare-hare bakeng sa ho phefumoloha; sebelisa super-oleophobic/hydrophobic surface post-therapy ntle le ho thibela pore.

Sengoliloeng sena se fana ka melemo ea lesela la mocheso o phahameng oa PTFE joalo ka mecha ea litaba ea mocheso o phahameng oa mocheso. Matla a tšeletseng a bohlokoa: Ho hanyetsa mocheso o ikhethang (260 ° C e tsoelang pele, tlhōrō ~ 300 ° C), e fetang PPS (190 ° C) le aramid (200 ° C); Ho se sebetse ho feteletseng ha lik'hemik'hale khahlanong le li-acids, alkalis, solvents le oxidants, hydrolysis-resistant, aramid e sa sebetseng hantle le P84 khase ea flue e senyang; Ts'ebetso e phahameng ea ho hloekisa lerōle e nang le matla a tlase a tlase haholo a nolofalletsang ho tlosa kuku ea lerōle habonolo le ho theoha ha khatello e tlase; Ts'ebetso e ntle haholo ea ho sefa ka boholo ba pore 0.1-3μm e hapang ho feta 99.99% ea likaroloana tsa PM2.5; Ho se be le mollo o nang le LOI ka holimo ho 95%, ka mekhoa e khahlanong le static e fumanehang; Matla a phahameng a mochini a tsoang ho matlafatso ea khalase ea fiberglass, e nang le mecha ea litaba e hloekileng ea PTFE e fanang ka maemo le> bophelo ba ts'ebeletso ea lilemo tse 4. E bapisa hantle khahlanong le PPS, aramid, Nomex, P84 le fiberglass filter media ho pholletsa le mocheso, khanyetso ea lik'hemik'hale, ho hanyetsa hydrolysis le ts'ebetso ea ho hloekisa.

Sehlooho sena se fana ka litharollo tse hlophisitsoeng bakeng sa ho thibela masala a sekhomaretsi le ho tsoa mali ka sekhomaretsi ha u sebelisa tepi ea mocheso o phahameng oa PTFE ho sireletsa menoana ea khauta ea PCB nakong ea kopano ea SMT. Tlhahlobo ea sesosa sa motso: masala a hlaha ka lebaka la ho hlōleha ho kopane kapa ho fetisoa ha sefahleho; ho tsoa mali ho hlaha ka lebaka la ho theoha ha viscosity le sekhomaretsi se phallang tlas'a mocheso oa reflow. Tharollo ea mantlha ke khetho e nepahetseng ea theipi: silicone PSA e nang le tlhōrō ea nako e khutšoanyane ≥300 ° C, e tsoelang pele ≥260 ° C, botenya bohle ba 0.08-0.13mm e nang le likarolo tse tšesaane tse khomarelang holimo, le setifikeiti se khahlanong le ho tsoa mali / masala. Taolo ea mehato e tšeletseng: ho hloekisa pele ho lamination ka IPA; lamination ea zero-tension e nang le phallo e feletseng ea moea; boemo bo ntlafalitsoeng ba mocheso oa phalliso ka ho futhumatsa ha bonolo (<2°C/s); ho ebola ho batang ka tlase ho 50 ° C ka lehlakoreng la 180 °; ts'ebetso ea hang-hang nakong ea lihora tse 24 le tšebeliso e le 'ngoe feela; ho hloleha ho sebetsana le ho hlakola IPA le tlhahlobo ea magnifier ea 40-50x. Bakeng sa li-PCB tse mahlakoreng a mabeli, nkela sebaka ka theipi e ncha pele e sebetsa ka lehlakoreng la bobeli.

Sehlooho sena se fana ka tataiso e hlophisitsoeng mabapi le ho thibela wrinkles ka PTFE phahameng-thempereichara lesela nakong sintering. Wrinkles ha e le hantle e bakoa ke ho fokotseha ho sa lekaneng ha mocheso le khatello ea maikutlo e sa tsitsang. Litharollo li koahela ts'ebetso e feletseng ea mosebetsi: taolo ea substrate e tala (e feletseng ea dewaxing / mocheso oa mocheso ho felisa khatello ea kelello ea ka hare); ho kenya le ho omisa (liaparo tse ngata tse tšesaane, mocheso o bonolo oa mocheso, li-roller tse sebetsang ka thata); taolo ea sebōpi sa sintering (1-3% e fetelletseng bakeng sa tumello ea ho fokotseha ha mocheso, taolo ea micro-tension e koetsoeng, ho feto-fetoha ha mocheso ka har'a ± 5 ° C, curve ea preheating-sintering-cooling curve, libopi tsa moea e le tharollo e nepahetseng, li-rollers tse kobehileng); ho pholisa le ho beha (ho pholisa butle butle, boloka ho hasana ho fihlela ka tlase ho 100 ° C, ho pholile ka ho feletseng pele ho tsoelipana); ho lekola marang-rang ka tlhahlobo e matla ea leseli le ho sekena ha infrared.

Sehlooho sena se hlahloba kamoo sandblasting kapa matt finishing treatment e amang sebopeho sa bokaholimo ba lesela la mocheso o phahameng oa PTFE. Liphetoho li etsahala ka litekanyo tse tharo: Microscopic morphology e fetoha ho tloha ho seipone se boreleli ho ea ho sebopeho se makukuno se nang le boleng bo phahameng ba Ra/Rz, ho theha 3D mechanical anchoring structures bakeng sa tlamahano e latelang. Botšepehi ba ho roala bo tobane le likotsi: PTFE layer thinning, exposure ea fiberglass substrate (e bakang tahlehelo ea thepa e sa thupeng, ho kenella ha mongobo, le ho fokotsa matla a mochine), hammoho le microcracks le litšila.

Sengoliloeng sena se hlahisa ts'ebetso e felletseng ea ho kenya lesela la fiberglass ka emulsion ea PTFE. Mehato e supileng ea bohlokoa: ① Pretreatment (dewaxing/desizing) ka 350-400°C ho tlosa lisebelisoa tsa boholo ba masela; ② Tlhahiso ea emulsion e nang le 40-55% e tiileng le li-surfactants bakeng sa ho koloba hantle; ③ Ho ima ka mokhoa oa dip-squeeze kapa ho roala ka lehare la ngaka; ④ Ho omisa ho 100-150 ° C ho fetola metsi ka bonolo 'me u thehe filimi e omileng ea PTFE; ⑤ Sintering ho 360-390 ° C (ho fihlela ho 400 ° C) ho qhibilihisa likaroloana tsa PTFE ka filimi e tsoelang pele; ⑥ Multi-cycle impregnation-drying-sintering e pheta-pheta makhetlo a 2-4 ho fihlela botenya ba sepheo le lihlahisoa tsa resin (45-65%); ⑦ Kalafo ea morao-rao e kenyeletsang phekolo ea corona, ho fokotsa moeli, ho koala le ho hlahloba boleng. Lintlha tsa taolo ea mantlha: dewaxing e felletseng, ho kolobisa ka botlalo emulsion, ho omisa butle-butle, mocheso o nepahetseng oa sintering, le letsoalo le sa fetoheng la ho roala. Lihlahisoa li fana ka li-laminate tsa koporo tse nang le maqhubu a phahameng, mabanta a conveyor a mocheso o phahameng le lisebelisoa tsa meralo ea meralo.