This article presents advantages of PTFE high-temperature cloth as high-temperature filter media. Six key strengths: Outstanding temperature resistance (continuous 260°C, peak ~300°C), exceeding PPS (190°C) and aramid (200°C); Extreme chemical inertness against acids, alkalis, solvents and oxidants, hydrolysis-resistant, outperforming aramid and P84 in corrosive flue gas; Superior dust cleaning performance with ultra-low surface energy enabling easy dust cake removal and sustained low pressure drop; Excellent filtration efficiency with pore sizes 0.1-3μm capturing over 99.99% of PM2.5 particles; Non-flammability with LOI above 95%, with anti-static options available; High mechanical strength from fiberglass reinforcement, with pure PTFE fiber media offering flexibility and >4 year service life. Compares favorably against PPS, aramid, Nomex, P84 and fiberglass filter media across temperature, chemical resistance, hydrolysis resistance and cleaning performance.

This article provides systematic guidance on preventing wrinkles on PTFE high-temperature cloth during sintering. Wrinkles are fundamentally caused by uneven thermal shrinkage and inconsistent stress. Solutions cover full workflow: raw material substrate control (complete dewaxing/heat setting to eliminate internal stress); impregnation and drying (multiple thin coatings, gentle temperature gradient, active drive rollers); sintering furnace control (1-3% overfeed for thermal shrinkage allowance, closed-loop micro-tension control, transverse temperature uniformity within ±5°C, gradient preheating-sintering-cooling curve, air-flotation furnaces as optimal solution, curved spreader rollers); cooling and setting (gradual slow cooling, maintain spreading until below 100°C, full cooling before winding); online monitoring with strong light inspection and infrared scanning.

This article analyzes how sandblasting or matt finishing treatment affects the surface structure of PTFE high-temperature cloth. Changes occur in three dimensions: Microscopic morphology transforms from smooth mirror-like to rough gully texture with sharply increased Ra/Rz values, creating 3D mechanical anchoring structures for subsequent bonding. Coating integrity faces risks: PTFE layer thinning, potential exposure of fiberglass substrate (causing loss of non-stick property, moisture penetration, and reduced mechanical strength), plus microcracks and debris generation.

This article introduces the complete basic process for impregnating fiberglass fabric with PTFE emulsion. Seven key steps: ① Pretreatment (dewaxing/desizing) at 350-400°C to remove textile sizing agents; ② Emulsion formulation with 40-55% solid content and surfactants for improved wetting; ③ Impregnation via dip-squeeze method or doctor blade coating; ④ Drying at 100-150°C to gently evaporate water and form dry PTFE film; ⑤ Sintering at 360-390°C (up to 400°C) to melt PTFE particles into continuous film; ⑥ Multi-cycle impregnation-drying-sintering repeated 2-4 times to reach target thickness and resin content (45-65%); ⑦ Post-treatment including corona treatment, edge trimming, winding and quality inspection. Core control points: complete dewaxing, full emulsion wetting, gradual drying, precise sintering temperature, and consistent coating density. Products serve high-frequency copper-clad laminates, high-temperature conveyor belts and architectural membrane materials.

This article introduces the organic solvents that PTFE high-temperature cloth can withstand. PTFE-coated fiberglass fabric exhibits exceptional chemical inertness, resisting nearly all common organic solvents under normal working conditions without dissolution, swelling or chemical reaction. Tolerable categories include: alcohols (methanol, ethanol, isopropanol), ketones (acetone, MEK, cyclohexanone), esters (ethyl acetate, butyl acetate), hydrocarbons (gasoline, toluene, xylene, hexane), halogenated hydrocarbons (dichloromethane, chloroform, carbon tetrachloride), ethers (diethyl ether, THF), organic acids (glacial acetic acid, formic acid), amines and amides (triethylamine, DMF), phenols, and others like carbon disulfide, pyridine, silicone oil and brake fluid.

This article covers cooling rate requirements during PTFE high-temperature cloth sintering. After sintering at 380-400°C, the fabric must rapidly pass through the 310-315°C crystallization-sensitive zone. Recommended cooling rate is at least 30-50°C/min (thin cloth can achieve 100-200°C/min via air cooling). Rapid cooling (quenching) produces low crystallinity (45-50%), yielding soft, tough coatings with smooth surfaces, strong adhesion, excellent non-stick performance, and resistance to delamination and cracking. Slow cooling (furnace cooling) results in high crystallinity (60-70%), causing rigid, brittle coatings prone to shrinkage, peeling and microcracks.

High-tensile PTFE high-temperature cloth is made by coating PTFE onto high-strength fiberglass fabric, offering tensile strength, heat resistance, non-stick properties, chemical resistance, and low friction. Key applications include: industrial conveying (heat shrink packaging, food baking, textile dryers, paper/film drying); composite molding release cloth and hot press cushion liners; welding protective curtains and thermal insulation jackets; electrical motor and transformer insulation; building sliding bearings and pipeline supports; chemical filtration and valve sealing in corrosive environments. High tensile strength ensures durability under tension, tearing, repeated flexing, and high-temperature mechanical stress across these diverse heavy-duty applications.

During sintering, PTFE particles on fiberglass fabric melt above 327°C, destroying original folded-chain lamellae and particle boundaries to form an amorphous melt. Upon cooling, PTFE recrystallizes into spherulites composed of radially oriented lamellae, with crystallinity ranging 50–70%. Cooling rate determines crystal perfection: slow cooling yields higher crystallinity, larger spherulites, greater hardness; rapid quenching gives finer spherulites and improved flexibility.

This technical brief from Jiangsu Aokai analyzes how excessively low or high sintering temperatures damage PTFE high-temperature cloth. Low sintering leaves particles unmelted, causing micro-pores, weak coating-substrate bonding, rough surfaces, poor mechanical strength, and milky opaque appearance. Overheating induces PTFE thermal degradation, generating pinholes, bubbles, brittleness, yellow-to-black discoloration, and releasing toxic fumes. Both extremes destroy compactness, non-stick performance, flexibility, insulation, and dimensional stability.

PTFE high-temperature cloth insulating gaskets combine high dielectric strength (stable under humidity), -70°C to 260°C temperature range, universal chemical resistance (except molten alkali metals), non-stick surface (prevents creepage), anti-creep (fiberglass reinforcement vs. pure PTFE), high tensile strength, low friction (μ=0.05-0.1), and V-0 flame rating. Compared to mica, rubber, and pure PTFE gaskets, PTFE cloth offers superior flexibility, processability, and long-term dimensional stability. Ideal for transformers, motor insulation, chemical flange sealing, and semiconductor equipment.